RC Lander 90mm 1000kv 8-10S Metal 12 Blade Dynamic Power EDF

RC Lander 90mm 1000kv 8-10S Metal 12 Blade Dynamic Power EDF
Click To Enlarge
  • Item #: RCL-LEDFADPS12B90-1A10/8S
  • Manufacturer: RC Lander
  • Manufacturer's Product Number: RCL-LEDFADPS12B90-1A16/6S
  • Condition: New
  * Marked fields are required.
Qty*
Price $229.99
Sale Price $199.99
Availability In-Stock

The RC Lander Dynamic Power Series 8-10S 12 Metal Blade EDF offers great durability with a full metal fan unit that offers good performance.

All RC Lander fans and motors are test run at the factory to ensure that they are in proper operating manner before being shipped out. The fans are put through a series of tests to ensure that they are operating as intended. Be sure to reference the instruction manual for proper motor and esc program settings.

FEATURES:

A lot of EDF units are made of plastic material which during operation creates high temperature. This results in loss of power and the possibiltiy of damage to the motor, battery or speed control. Heat sinks help, but this only offers average improvement. RC Lander Technology uses special metals to imporve dissapation of heat in their EDF units. The shroud, spinner and tail pipe are made with a special aluminum alloy that is efficient at heat dissapation. Because of this, the whole shroud acts as a heat sink, removing heat from the motor. The motor and fan unit comes assembled and balanced from the factory. A thermal grease compound is used between the motor and shroud to further help dissipate heat. This is the same compound that is used in computer processors and heat sinks. This design creates a more efficiently running motor and will provide peak performance while extending the lifespan of the motor.

BUILDERS NOTE: REFER TO THE "ELECTRIC SETUP GUIDELINE" ON THE HOME PAGE TO HELP DETERMINE THE PROPER SET UP FOR FAN, ESC, MOTOR AND BATTERY.

SPECIFICATIONS:  
 Material:  Aluminum Alloy
 Weight:  1.47lb/ 670g
 Rotor:  90mm, 12 bladed aluminum
 Outer Diameter:  94mm
 Motor:  4 Pole Inrunner
8s Specs:  
 Max RPM (8s):  45,000
 Power (10 Sec Burst):  3,500 Watts
 Power:  3,200 Watts
 KV Rating:  1,000kv
 Current:  110 Amps
 Battery:  8s/ 29.6V Lipo w/ 40C or higher
 Thrust (Estimated):*  Up to 4.6kg/ 10.1 lb.
10s Specs:  
Max RPM (10S):  48,000
Power (10 Sec Burst):  5,000 Watts
Power:  4,800 Watts
KV Rating:  1,000kv
Current:  135 Amps
Battery:  10s/ 37V Lipo w/ 40C or higher
Thrust (Estimated):*  Up to 5.4kg/ 11.9 lb.
Speed Control Settings:  
 Start:  Soft
 Timing:  High
 Speed Control:  130 amp or higher

 *(Estimated dependant upon lipo battery quality, air ducting, esc etc..)

Picture notice: The kv of the motor is 1000kv.  RC Lander does not make a 1700kv edf unit.  That is an error on RC Lander's part to have that stated in the picture.

WARNING:Operating the motor outside of the specifications listed above can either damage the motor, battery or esc. It is important that these components are set up properly. Failure to do so can void the warranty. It is strongly encouraged to use a Watt Meter to test the watt and amp performance when setting up a new system. If the output is above the factory recommended specs, then it needs to be adjusted by the esc. The timing and throttle settings on the esc can help to set the appropriate levels.

Related Items